Photocatalytic and Gas Sensitive Multiwalled Carbon Nanotube/TiO2-ZnO and ZnO-TiO2 Composites Prepared by Atomic Layer Deposition.

TiO2 and ZnO single and multilayers were deposited on hydroxyl functionalized multi-walled carbon nanotubes using atomic layer deposition. The bare carbon nanotubes and the resulting heterostructures were characterized by TG/DTA, Raman, XRD, SEM-EDX, XPS, TEM-EELS-SAED and low temperature nitrogen adsorption techniques, and their photocatalytic and gas sensing activities were also studied. The carbon nanotubes (CNTs) were uniformly covered with anatase TiO2 and wurtzite ZnO layers and with their combinations. In the photocatalytic degradation of methyl orange, the most beneficial structures are those where ZnO is the external layer, both in the case of single and double oxide layer covered CNTs (CNT-ZnO and CNT-TiO2-ZnO). The samples with multilayer oxides (CNT-ZnO-TiO2 and CNT-TiO2-ZnO) have lower catalytic activity due to their larger average densities, and consequently lower surface areas, compared to single oxide layer coated CNTs (CNT-ZnO and CNT-TiO2). In contrast, in gas sensing it is advantageous to have TiO2 as the outer layer. Since ZnO has higher conductivity, its gas sensing signals are lower when reacting with NH3 gas. The double oxide layer samples have higher resistivity, and hence a larger gas sensing response than their single oxide layer counterparts.

High Aspect-Ratio Iridium-Coated Nanopillars for Highly Reproducible Surface-Enhanced Raman Scattering (SERS).

A variety of different gold and silver nanostructures have been proposed over the years as high sensitivity surface-enhanced Raman scattering (SERS) sensors. However, efficient use of SERS has been hindered by the difficulty of realizing SERS substrates that provide reproducible SERS response over the whole active area. Here, we show that atomic layer deposition (ALD) grown iridium can be used to produce highly reliable SERS substrates. The substrates are based on a periodic array of high aspect-ratio iridium coated nanopillars that feature efficient and symmetrically distributed hot spots within the interpillar gaps (gap width<10 nm). We show that the enhancement with the iridium based nanostructures is of significant magnitude and it equals the enhancement of silver based reference substrates. Most notably, we demonstrate that the ordered and well-defined plasmonic nanopillars offer a measurement-to-measurement variability of 5%, which paves the way for truly quantitative SERS measurements.

High resolution double-sided diffractive optics for hard X-ray microscopy.

The fabrication of high aspect ratio metallic nanostructures is crucial for the production of efficient diffractive X-ray optics in the hard X-ray range. We present a novel method to increase their structure height via the double-sided patterning of the support membrane. In transmission, the two Fresnel zone plates on the two sides of the substrate will act as a single zone plate with added structure height. The presented double-sided zone plates with 30 nm smallest zone width offer up to 9.9% focusing efficiency at 9 keV, that results in a factor of two improvement over their previously demonstrated single-sided counterparts. The increase in efficiency paves the way to speed up X-ray microscopy measurements and allows the more efficient utilization of the flux in full-field X-ray microscopy.

X-ray ptychographic computed tomography at 16 nm isotropic 3D resolution.

X-ray ptychography is a scanning variant of coherent diffractive imaging with the ability to image large fields of view at high resolution. It further allows imaging of non-isolated specimens and can produce quantitative mapping of the electron density distribution in 3D when combined with computed tomography. The method does not require imaging lenses, which makes it dose efficient and suitable to multi-keV X-rays, where efficient photon counting, pixelated detectors are available. Here we present the first highly resolved quantitative X-ray ptychographic tomography of an extended object yielding 16 nm isotropic 3D resolution recorded at 2 Šwavelength. This first-of-its-kind demonstration paves the way for ptychographic X-ray tomography to become a promising method for X-ray imaging of representative sample volumes at unmatched resolution, opening tremendous potential for characterizing samples in materials science and biology by filling the resolution gap between electron microscopy and other X-ray imaging techniques.

Programming nanostructured soft biological surfaces by atomic layer deposition.

Here, we present the first successful attempt to programme the surface properties of nanostructured soft biological tissues by atomic layer deposition (ALD). The nanopatterned surface of lotus leaf was tuned by 3-125 nm TiO2 thin films. The lotus/TiO2 composites were studied by SEM-EDX, XPS, Raman, TG-DTA, XRR, water contact angle and photocatalysis measurements. While we could preserve the superhydrophobic feature of lotus, we managed to add a new property, i.e. photocatalytic activity. We also explored how surface passivation treatments and various ALD precursors affect the stability of the sensitive soft biological tissues. As we were able to gradually change the number of nanopatterns of lotus, we gained new insight into how the hollow organic nanotubes on the surface of lotus influence its superhydrophobic feature.

Ultra-high resolution zone-doubled diffractive X-ray optics for the multi-keV regime.

X-ray microscopy based on Fresnel zone plates is a powerful technique for sub-100 nm resolution imaging of biological and inorganic materials. Here, we report on the modeling, fabrication and characterization of zone-doubled Fresnel zone plates for the multi-keV regime (4-12 keV). We demonstrate unprecedented spatial resolution by resolving 15 nm lines and spaces in scanning transmission X-ray microscopy, and focusing diffraction efficiencies of 7.5% at 6.2 keV photon energy. These developments represent a significant step towards 10 nm spatial resolution for hard X-ray energies of up to 12 keV.

Dense high aspect ratio hydrogen silsesquioxane nanostructures by 100 keV electron beam lithography.

We investigated the fabrication of dense, high aspect ratio hydrogen silsesquioxane (HSQ) nanostructures by 100 keV electron beam lithography. The samples were developed using a high contrast developer and supercritically dried in carbon dioxide. Dense gratings with line widths down to 25 nm were patterned in 500 nm-thick resist layers and semi-dense gratings with line widths down to 10 nm (40 nm pitch) were patterned in 250 nm-thick resist layers. The dense HSQ nanostructures were used as molds for gold electrodeposition, and the semi-dense HSQ gratings were iridium-coated by atomic layer deposition. We used these methods to produce Fresnel zone plates with extreme aspect ratio for scanning transmission x-ray microscopy that showed excellent performance at 1.0 keV photon energy.

Fabrication of nanocluster silicon surface with electric discharge and the application in desorption/ionization on silicon-mass spectrometry.

This study presents a new, simple, and low-cost technique to fabricate a nanocluster silicon (NCSi) surface on planar silicon using a micro-scale direct current (DC) discharge under ambient conditions. The method requires no masks, chemicals, vacuum environment, or laser, but only a high-voltage supply. The NCSi surfaces, characterized by scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy, consist of oxidized silicon nanoclusters 50-200 nm in diameter, likely formed by melting due to high temperatures in the discharge. The minimum size of the NCSi spot is determined by the size of the discharge tip (approximately 90 microm). Arbitrary NCSi areas can be produced on a silicon wafer by moving the discharge needle on the surface with the help of a computer-controlled xyz stage. NCSi surfaces can also be formed on three-dimensional (3D) surfaces, as demonstrated with silicon micropillars. NCSi surfaces can be used, for example, in various analytical applications. In this study, we demonstrate their use as sample plates in the analysis of drugs and peptides with desorption/ionization on silicon-mass spectrometry (DIOS-MS).